PURSUANT to subsection 5.9(2) of the Aeronautics Act, and after taking into account that the exemption is in the public interest and is not likely to affect aviation safety, I hereby exempt persons installing parts on Canadian registered aircraft or on an aeronautical product intended for installation on a Canadian registered aircraft from paragraphs 571.07 (c), (d), (e), (f), (g) and (h) (Installation of New Parts) of the Aircraft Maintenance Requirements Standard (571) made pursuant to section 571.07 of the Canadian Aviation Regulations.
These provisions attached at Annex 1 of this exemption, limit the eligibility of Federal Aviation Administration Parts Manufacturing Approval (FAA PMA) part installation on Canadian registered aircraft or on other aeronautical products to be installed thereon. This exemption is subject to the conditions set out below.
PURPOSE
The purpose of this exemption is to relieve persons installing FAA PMA parts on a Canadian registered aircraft or on an aeronautical product intended for installation on a Canadian registered aircraft from the restrictions set out in paragraphs 571.07 (c), (d), (e), (f), (g) and (h) (Installation of New parts) of the Aircraft Maintenance Requirements Standard (571) which pertain to the eligibility of FAA PMA part installation on Canadian registered aircraft. The effect of the exemption is to provide installers of parts on Canadian registered aircraft or other aeronautical products intended for installation on a Canadian registered aircraft, with additional acceptable sources of supply of parts.
APPLICATION
The exemption applies to persons installing FAA PMA parts on a Canadian registered aircraft or on an aeronautical product intended for installation on a Canadian registered aircraft.
CONDITIONS
This exemption is subject to the following conditions:
- The part shall be marked in accordance with FAA PMA part marking requirements set out by the Federal Aviation Administration;
- The part shall be certified by the part manufacturer, as conforming to the design data, approved by the Federal Aviation Administration or by Transport Canada Civil Aviation, through a certificate of conformity;
- The certificate of conformity set out in condition 2 shall indicate the aeronautical product(s) for which it is eligible;
- If the certificate of conformity is issued by a person other than the FAA PMA holder, the certificate shall indicate that the production approval holder has authorized direct shipment; and
- The installer of parts shall comply with all other requirements of the Canadian Aviation Regulations.
VALIDITY
This exemption is in effect until the earliest of the following:
- ÉST at midnight October 1, 2006;
- the date on which any condition set out in this exemption is breached;
- the date on which an amendment to the appropriate provisions of the Canadian Aviation Regulations comes into effect; or
- the date on which this exemption is cancelled in writing by the Minister where he is of the opinion it is no longer in the public interest, or is likely to affect aviation safety.
Dated at Ottawa, Ontario this 31st day of March, 2005, on behalf of the Minister of Transport.
Donald Sherritt
Director
Aircraft Maintenance and Manufacturing
Annex 1
Paragraphs (c) through (h) inclusive of Standard 571.07 "Installation
of New Parts" read as follows:
"(c)
- Parts made to an FAA Parts Manufacturer Approval (hereinafter simply known as PMA) can be installed on aeronautical products for which the US has jurisdiction for the initial type design.
- Except as provided in (e), (f), (g) and (h), PMA parts can be installed on other aeronautical products only where specified in the type design, in the manufacturer's parts catalogue, or where approved by the Civil Aviation Authority of the country having jurisdiction over the initial type design.
- An aircraft that is not of US type design and that was operated with PMA parts installed while the aircraft was under the jurisdiction of another State, can be accepted as a Canadian aircraft provided the PMA parts were installed in compliance with the regulations of the other State.
- An aeronautical product, other than a complete aircraft, that is not of US type design but was operated with PMA parts installed while under the jurisdiction of another State, can remain in service on a Canadian aircraft provided the PMA parts were installed in compliance with the regulations of the other State.
- A PMA part accepted pursuant to (e) or (f) can remain in service until such time as its replacement is required by reason of deterioration of time in service. Such a part shall not, however, be replaced by another FAA PMA part.
- PMA parts are replacement parts and are acceptable on Canadian aircraft for which TC has jurisdiction over the initial design, if such parts are listed in the manufacturer's parts catalogue, or otherwise approved by the Minister.
Information Note:
Installation of an FAA PMA part not meeting these criteria constitutes
a modification requiring compliance with Section 571.06 of the CARs. "
- Date de modification :